Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
We have unearthed the article pertaining to How to Install a Bathtub Yourself listed below on the net and reckoned it made sense to discuss it with you in this article.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub and set in the new one. Ensure you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly help you install a new bathtub in your restroom if you have already gotten a brand-new bathtub and also do not require to transform the plan of your previous water system pipelines.
Your devices and material checklist should make up the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reads level.
To mount faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leakages and tighten them if essential. Fill the tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with moisture as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our post about Installing A Bathtub. Thank you so much for taking the time to read our piece. Enjoyed our article? Please share it. Help others locate it. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Schedule An Appointment Report this page